On Feb 4, 5:24 pm, "Doug Lassiter" > wrote:
> Have had a Weber Silver gas grill for several years, and I'm largely
> pleased with it. Lately, the heat doesn't seem quite as intense. I can
> put my hand over the grill for 7-8 seconds on hi. That's not a real
> "sear" kind of heat. This is NOT the well known gas leak safety
> throttle issue -- I get temps up to about 450F when closed. When I
> look at the flame bars, the little flames coming out of the gas holes
> (must be several hundred) are not uniform in length. Some are an inch
> long, and some are a quarter of an inch long. That is to say, it looks
> like the flame bar isn't shooting enough gas through many of the
> little holes.
>
> Well, OK, I take my pocketknife and jam it in one of the little gas
> holes/slits, and I can make the quarter inch flame from that one turn
> into an inch long flame. So ... it looks like these little buggers are
> getting clogged up.
>
> So is there a straightforward practice to cleaning these out? Um, the
> pocketknife trick is not that convenient.
>
> Looks to me like a small drill bit could make a major difference here.
> Just make a bunch of bigger holes! But do I dare?
>
> Is this a recognized issue for this kind of grill? Yeah, I'll try
> alt.food.barbeque if I can't get an answer here.

Go to the hardware store, get a wire brush...

Thanks for the suggestions. It sounds like removal of the flame bars
followed by a good soaking and pressure wash is the way to go. As to
reaming out the holes or wire brushing them, the holes in the Weber
Silver flame pipes are very small slits. As I said, I can get my small
pocketknife blade in them a bit, but not much. Brushing them will
likely clog them more with metal flakes, and reaming them out is
simply not possible. I could stick my tiny blade in each one a bit,
but that would take a long time to do them all, and may just
temporarily push the clog aside, instead of really removing it.

On Feb 5, 8:03 pm, "Doug Lassiter" > wrote:
> Thanks for the suggestions. It sounds like removal of the flame bars
> followed by a good soaking and pressure wash is the way to go. As to
> reaming out the holes or wire brushing them, the holes in the Weber
> Silver flame pipes are very small slits. As I said, I can get my small
> pocketknife blade in them a bit, but not much. Brushing them will
> likely clog them more with metal flakes, and reaming them out is
> simply not possible. I could stick my tiny blade in each one a bit,
> but that would take a long time to do them all, and may just
> temporarily push the clog aside, instead of really removing it.

You can also buy a new burner tube for less than $20. There are 3rd
party kits at most hardware stores. Takes about 5 minutes to install.

On Feb 6, 10:40 am, "Will" > wrote:
> On Feb 5, 8:03 pm, "Doug Lassiter" > wrote:
>
> > Thanks for the suggestions. It sounds like removal of the flame bars
> > followed by a good soaking and pressure wash is the way to go. As to
> > reaming out the holes or wire brushing them, the holes in the Weber
> > Silver flame pipes are very small slits. As I said, I can get my small
> > pocketknife blade in them a bit, but not much. Brushing them will
> > likely clog them more with metal flakes, and reaming them out is
> > simply not possible. I could stick my tiny blade in each one a bit,
> > but that would take a long time to do them all, and may just
> > temporarily push the clog aside, instead of really removing it.
>
> You can also buy a new burner tube for less than $20. There are 3rd
> party kits at most hardware stores. Takes about 5 minutes to install.

the finest potracks in the world can be found at http://www.modernblacksmith.com

"dan" > wrote in message
>
> the finest potracks in the world can be found at
> http://www.sleazyblacksmith.com
>


You really are a sleazy spammer

On Feb 11, 10:26 pm, "Edwin Pawlowski" > wrote:
> "dan" > wrote in message
>
> > the finest potracks in the world can be found at
> >http://www.sleazyblacksmith.com
>
> You really are a sleazy spammer

spam is unsolicited email. I never emailed anyone....

On Feb 11, 10:44 pm, "dan" > wrote:
> On Feb 11, 10:26 pm, "Edwin Pawlowski" > wrote:
>
> > "dan" > wrote in message
>
> > > the finest potracks in the world can be found at
> > >http://www.sleazyblacksmith.com
>
> > You really are a sleazy spammer
>
> spam is unsolicited email. I never emailed anyone....

"don't clean your pans for thirty years...." Mr. ed "botulisim"
pawlozky.... good advise ED

"dan" > wrote in message
ups.com...
> On Feb 11, 10:26 pm, "Edwin Pawlowski" > wrote:
>> "dan" > wrote in message
>>
>> > the finest potracks in the world can be found at
>> >http://www.sleazyblacksmith.com
>>
>> You really are a sleazy spammer
>
> spam is unsolicited email. I never emailed anyone....
>

You used a USENET newsgroup for commercial purposes. That is against the
Terms of Service of your internet provider. These groups are for the
discussion of a subject and not for commercial advertising.

dan wrote:
> On Feb 11, 10:26 pm, "Edwin Pawlowski" > wrote:
>> "dan" > wrote in message
>>
>>> the finest potracks in the world can be found at
>>> http://www.sleazyblacksmith.com
>>
>> You really are a sleazy spammer
>
> spam is unsolicited email. I never emailed anyone....

Spam is also a term that applies to usenet. Or did you miss that email?
http://www.templetons.com/brad/spamterm.html

"Edwin Pawlowski" > wrote in message
. net...
>
> "dan" > wrote in message
>>
>> the finest potracks in the world can be found at
>> http://www.sleazyblacksmith.com
>>
>
>
> You really are a sleazy spammer
>

You're right there.......& its into the killfile for this dork!